For the
Modern Christmas Table Runner Swap, we are encouraged to also send a handmade holiday ornament. I was stumped. I looked at a lot of flickr and pinterest ideas, many of which are stunning. I wanted an ornament that was modern, yet also had traditional patchwork, and that would easily fit in a shipping envelop. I love trees, and after looking at many variations on the tree ornament, I came up with this.
My stylized triangle tree is modern and has clean, simple lines. And it is traditional, composed of nice tiny 1/2" finished patchwork squares. There are many versions of this idea on the internet; this is just my take.
And it is far easier to make these trees than you might think, even though a tree ornament that is 3.5" high uses 28, 1" squares. This is a perfect project for tiny scraps. Let me know what you think of my tutorial and if you have any questions I would be happy to help. If you make some of these ornaments, I would love it if you would let me know.
1 - Cut a number of 1" strips from your scraps to make the squares. Each larger (3.5" tree) uses 28 squares.
2 - Cut your 1" strips into 1" squares.
3 - Lay out your 1" squares. For a 3.5" tree, you start with a row of 7 squares, then 6 squares, 5, squares, 4 squares, 3 squares, 2 squares and 1 square. To change this pattern to make larger or smaller trees, just add or subtract rows.
4 - Sew the squares together. I start by chain piecing pairs, being careful to always start from the same end and do as many pairs as each row will allow.
5 - Chain piecing the pairs using a 1/4" seam. These are only 1" squares so they will be 1/2" squares once finished. Piecing small bits is not hard if you sew slowly.
6 - Once you have pieced all the pairs in order, cut them apart in reverse order and put them back in their places. I am careful to take my time to keep them in the order I started with.
Then sew the pairs to the other pairs and to the left over end pieces, again in order, until you have finished sewing each row.
7 - Press each row. I pressed the seams in one direction for one row and the opposite for the row above it to distribute the bulk. Lay out the rows again.
8 - Place the 7 piece row and the 6 piece row together, right sides facing. Eyeball the fit so that the 6 piece row is centred over the 7 piece row with an even amount showing on each end.
9 - Here is a close up of the overlap. Sew the rows together with 1/4" seam. I did not bother to pin but again moved slowly with the machine while sewing.
10 - This is how the rows look once sewn together. The blocks should be staggered like a brick wall.
11 - Position the next row in the same manner, placing it mid way between the ends of the row before and then sew into position.
12 - Here are all the rows sewn together. At this point it is important to give it a good press. I pressed all the seams toward the top of the tree. Be careful with the steam, as the alignment of the rows can easily stretch, but once you have it nicely pressed, a good shot of steam is helpful so all those seams lay flat.
13 - Lay the pressed pieced squares on a scrap of batting and roughly cut around the edge of the batting.
14 - Lay the pieced squares and batting on top of your back fabric. Make sure the back fabric is facing away so the wrong sides are facing each other.
15 - Trim the back fabric and pin the unit together. Three pins are enough for this size tree, be careful that the points are not too close to the edges.
16 - Line up your ruler from the mid point of the top square to the bottom corner of the bottom row outside square. I just eyeballed these positions.
17 - Cut off the edge. If you pins are sticking too far out you will need to adjust them first.
18 - Line up your ruler with the tree top point (at the bottom of this picture) and the outside edge of the other side of the bottom row. Cut off the excess.
19 - Measure 1/2" from the seam on the bottom row, using the bottom row seam as your guide. Cut off the extra from the tree bottom.
20 - Sew around the edge of the triangle, using a 1/4" seam. I just used my 1/4" foot but a walking foot would also work, maybe even better. I back stitched at the beginning and end of the sewing. If you wanted, you could add more quilting to the tree.
21 - After sewing the triangle the seams are probably no longer clean due to sewing the layers and all the little seams. I then measured 1/8" from each line of stitching by lining my ruler with the line of stitching. Then I trimmed off the outside bit.
22 - Here are three trees, before adding the hanging strings. The larger ones are about 3.5" from point to base and use 28 squares. The smaller one is about 2" high. (I don't think I did a final trim on that little one, might go back and do that now). You can make these trees any size, just add or subtract rows. Another way to alter the size is to use larger squares to start with.
23 - To add a piece of shiny yarn or string as a hanger, just poke your needle between the stitches at the point of the tree and pull through. I knotted the ends.
Here are the three I made this morning hanging from my sewing machine's thread thingy (I bet it has a name) this morning. It took me about 2 hours to cut the squares, make these three and take all the pictures as I went.
I like the mix of clean modern lines and traditional patchwork. It would be easy to make other shapes too. I am thinking of circles to represent glass ornaments and squares to represent presents, for example.
By the way, for those of you who love fabric, these fabrics were from left over bits of a charm pack and some fat quarters of Kate Spain's Twelve Days of Christmas fabrics.
p.s. I have linked this to the Pink Chalk Studio, Handmade with Love Tutorial Contest. There are a lot of wonderful tutorials there, have a look.
Best,
Leanne
